Projects
Improving the ARRL EFHW
11/7/2026
The ARRL EFHW kit, rebranded from HF kits, is an all-inclusive, relatively easy to build kit that provides moderately efficient matching for the included 40m half wave wire. Its primary limitation is the included FT240-43 toroid and winding, which isn’t the most efficient and limited to QRP power levels for high duty cycle modes such as FT8. An easy ~$10 upgrade to this kit is to instead use the Fair-Rite 2643251002 toroid (purchased separately) and wind it as an autotransformer.
An autotransformer is more efficient as there is no galvanic isolation between the antenna and the coax - it’s wound with a continuous piece of wire. An autotransformer with this toroid has been found to be ~90% power efficient (0.5 dB insertion loss) vs. ~80% (1dB) for one built per the instructions in the kit. You’ll likely never notice this slight improvement on the air as skywave propagation is far more variable than this even over short timeframes. The bigger upside is that this coupler will handle about twice as much power as the amount of power converted into heat is cut in half (from ~20% to ~10%).
Building this autotransformer is simple: just make 14 closely wound turns (blue wire in the diagram) and tap the winding at the second complete turn by soldering a second wire (red wire) to it (after scraping off the coating at the tap point). The magnet wire that came in the ARRL kit was sufficiently long for all of this. I even had enough to add an additional turn and tap (as shown in the second image) to test a 56:1 configuration, which I ended up not using. I was able to secure the autotransformer to the included board with two tie wraps by offsetting the core to one side of the board as shown in the third image. The hole spacings were not designed for this core geometry but this placement allows the board to be used without having to drill additional holes. I decided to use the original FT240-43 core as a choke.
My experience with this upgraded coupler is that it easily handles 50 W on FT8 (the maximum I’ve ever used), should be capable of 100W FT8, and I’ve not had any issues running 600W PEP through it for SSB for short periods. I’ve been using it for a few years now and have been very pleased with the results. I see no downside to this inexpensive upgrade.
Emacs Packages for Amateur Radio
11/7/2026
I’ve been an avid user of Emacs for its org-mode capabilities and for general file editing. I noticed that most of the things I was doing with amateur radio software was or could be represented with text. So, I’ve been developing Emacs packages for contact logging, ADIF file editing, spot monitoring, HF propagation condition monitoring, and even remote rig control. Essentially, I’m working on what’s needed for Emacs to function as the only amateur radio software interface I need for operating in the shack or for remote operation. It’s a fully customizable minimalist interface and requires little in terms of compute power such that a Raspberry Pi Zero 2W is sufficient for the shack or remote system.
My first two packages, QSO and ADIF-mode, are now available on MELPA. For access to all my software packages and projects see my GitHub page. Everything is free and under a GPL 3.0 license.
QRP
11/7/2026
Knowing what I know now from experience, I’m enjoying what I can do with HF QRP radios, especially with the power efficiency of CW, and all within the constraints of something very small and light. I’ve found the key to success with QRP begins with a good understanding the relationship between transmitter power, antenna gain (in the direction of interest), receive antenna gain, and propagation. Transmitter power can overcome a lot, so when you’re living with less you need to focus more on the other parts of the link budget that you can control - your antenna (including your transmission line, connectors, and impedance matching components). Even when you do you’ll still be more dependent on good ionospheric conditions than you would be with QRO.
When working DX, timing and patience is everything but typically once the DX hears “QRP” they will prioritize you. When calling CQ a QRP station is more likely to get a pileup. So, it’s really a mixed bag, and that’s why it’s not for everyone. I often switch between QRO and QRP depending on the situation and whim. I wouldn’t recommend QRP to a new ham, but for the more experienced ham who enjoys a challenge.
The cost of entry can be relatively low, with transceiver kits starting at ~$60 and fully assembled multiband transceivers for less than $160. I personally recommend QRP Labs for kits and lower cost gear and Elecraft for the best equipment if cost isn’t an issue.